JR128-R01-RTR-PRO
1/28 2WD indoor RACER /
READYSET-PRO
JR128-R01 series models
are ultra small high performance 2WD indoor racing
cars with a lot of very advanced opportunities for fine tuning and car setup,
which
you might find very surprising in a car of this very small size.
9 built-in ball bearings,
an adjustable ball differential with 64dp fine pitch and a
1S / 3.7V Lipo battery + charger make you really ready to race out of the box.
The cars are already
equipped with a 12mm micro servo for steering, a small
2.4 GHz receiver and an ESC (Electronic Speed Controller) running with
1S / 3.7V Lipo batteries, providing 5.5V current for receiver and steering.
Various other commercially
available steering servos, micro receivers and micro
car ESCs for brushed or brushless motors from other brands can be built in and
used in this car. (Attention: Do not use motors with less than 40 turns (40T)
togehter with this ESC, to avoid damage of the ESC!)
Ask your dealer for our brushless
motor and ESC - system and for our 2S Lipo batteries,
if you need 8.4V power supply for your preferred electronics.
The chassis offers the following features:
· Caster-angle
at front suspension adjustable in three positions: 1.1°, 2.7°, 4.4°.
· Camber-angle
at front suspension left and right adjustable: from 0° to -2.5°.
· Toe-in /
Toe-out adjustable at: 0°, +1°, +2°, -1°, -2°.
· Droop
limits at front suspension free adjustable.
· Adjustable
springs at front suspension.
· Ground
clearance front and rear adjustable on 4 levels in steps of 0.7mm.
· Longitudinal
damper with spring and droop-spring fully adjustable.
· Cross-dampers
with springs for fine tweak adjustment.
· Rear
scale body holder adjustable in height with included washers.
· Second rear scale body holder for wider scale bodies included.
· Front
scale body holder set adjustable to most scale bodies from other brands
for wide front and 98mm or 102mm
wheelbase.
Content of the Box:
Fully
assembled Ready to Run JR128-R01 PRO RC Car:
· High
Resistance Professional Chassis
· Jomurema
Design GT01 Body
· Adjustable
Front Suspension
· Adjustable
Rear Suspension
· 9x Ball
Bearings
· Ball
Differential (V-Groove PN)
· Brushed
Stock Motor / 130 Class
· FS-GT2 /
2.4GHz digital proportional Receiver
· 12mm
Steering-Servo;
· 1S / 3.7V
programmable brushed ESC
Lithium
Polymer (Lipo) Battery:
· 1S / 3.7V
/ 840mAh / 25C Lipo Battery
Manuals
and Decal:
· Manual
for JR128-R01-PRO indoor Racer
· Color
Decal for Car Body
Charger
for Lipo Battery:
· 1S / 3.7V
/ Lipo Charger
· Approx.
1A charging Current
Miscellaneous
Parts and Tools (8 Bags):
· Cross-Screwdriver;
Hex-Wrench-1.5mm; +3 different plastic Tools
· Front
Body-Holder-Adjustment-Set for many other Car Bodies
· Miscellaneous
adjustment Parts and Washers
· Steering-
Servo-, Rear Body-Holder and Adjustment Parts
· Other
Pinions and replacement Gear for Change of Car-Speed
· Steel-
and Replacement Parts and Springs for Change of Setup
· O-Rings
for Replacement
· Screws
for Replacement
· All
plastic Parts from plastic RTR-Set
FS-GT2 /
2.4 GHz digital proportional Radio
Transmitter:
· Channels:
2channels; Model type: car / boat
· RF power:
less than 20dbm; Modulation: GFSK
· Code
type: digital; Sensitivity: 1024
· Low
voltage warning: yes (less than 9V)
· DSC port:
yes (3.5mm); Charger port: yes
· Power:
12vdc (1.5AA*8); Weight: 328g
· ANT
length: 26mm;
· Size:
159*99*315mm; Color: black
· Certificate:
CE, FCC;
Attention:
8x AA-Batteries for Transmitter required, but not included!